Types of Shift Registers

Types of Shift Registers

AU May-06, 19, Dec.-06, 19

Serial In Serial Out (SISO) Shift Register

Shift Left Mode

• Fig. 4.3.1 shows serial-in serial-out shift-left register.

• We will illustrate the entry of the four bit binary number 1111 into the register, beginning with the left-most bit. Initially, register is cleared.

So Q_AQ_BQ_CQ_D = 0000

• The Table 4.3.1 summarizes the shift left operation.

• Fig. 4.3.2 shows waveforms for shift left operation

Shift Right Mode

• Fig. 4.3.3 shows serial-in serial-out shift-right register.

• We will illustrate the entry of the four bit binary number 1111 into the register, beginning with the left-most bit. Initially, register is cleared.

So Q₃Q₂Q₁Q₀= 0000

• Table 4.3.2 summarizes the shift right operation.

• The Fig. 4.3.4 shows waveforms for shift right operation.

Serial In Parallel Out (SIPO) Shift Register

•The data bits are entered serially into the register but the output is taken in parallel.

• Once the data are stored, each bit appears on its respective output line and all bits are available simultaneously as shown in Fig. 4.3.5.

Parallel In Serial Out (PISO) Shift Register

• In this type, the bits are entered in parallel i.e simultaneously into their respective stages on parallel lines.

• Fig. 4.3.6 illustrates a four-bit parallel in serial out register.

• There are four input lines A₃, A₂, A₁, A₀ for entering data in parallel into the register.

•  is the control input which allows shift or loading data operation of the register.

• When  is low, gates G₁, G₂, G₃ are enabled, allowing each input data bit to be applied to D input of its respective flip-flop.

• When a clock pulse is applied, the flip-flops with D = 1 will SET and those with D = 0 will RESET.

• All four bits are stored simultaneously.

• When  is high, gates G₁, G₂, G₃ are disabled and gates G₄, G₅, G₆ are enabled. This allows the data bits to shift right from one stage to the next.

• The OR gates at the D-inputs of the flip-flops allow either the parallel data entry operation or shift operation, depending on which AND gates are enabled by the level on the  input.

Parallel In Parallel Out (PIPO) Shift Register

• In 'parallel in parallel out register', there is simultaneous entry of all data bits and the bits appear on parallel outputs simultaneously.

• Fig. 4.3.7 shows this type of register.

Bidirectional Shift Register

• This type of register allows shifting of data either to the left or to the right side. It can be implemented by using logic gate circuitry that enables the transfer of data from one stage to the next stage to the right or to the left, depending on the level of a control line.

• Fig. 4.3.8 illustrates a four-bit bidirectional register.

• The  is the control input signal which allows data shifting either towards right or towards left.

• A high on this line enables the shifting of data towards right and a low enables it towards left.

• When  signal is high, gates G₁, G₂, G₃, G₄ are enabled.

• The state of the Q output of each flip-flop is passed through the D input of the following flip-flop.

• When a clock pulse arrives, the data are shifted one place to the right.

• When the  signal is low, gates G₅, G₆, G₇, G₈are enabled.

• The Q output of each flip-flop is passed through the D input of the preceding flip-flop.

• When clock pulse arrives, the data are shifted one place to the left.

Bidirectional Shift Register with Parallel Load

• When parallel load capability is added to the shift register, the data entered in parallel can be taken out in serial fashion by shifting the data stored in the register. Such a register is called bidirectional shift register with parallel load.

• Fig. 4.3.9 shows bidirectional shift register with parallel load.

• As shown in the Fig. 4.3.9, the D input of each flip-flop has three sources: Output of left adjacent flip-flop, output of right adjacent flip-flop and parallel input. Out of these three sources one source is selected at a time and it is done with the help of decoder. The decoder select lines (SL₁ and SL₀) select the one source out of three as shown in the Table 4.3.4.

• When select lines are 00 (i.e.SL₁= 0 and SL₀= 0 data from the parallel inputs is loaded into the 4-bit register.

• When select lines are 01 (i.e. SL₁= 0 and SL₀= 1), data within the register is shifted 1-bit left..

• When select lines are 10 (i.e.SL₁=1 and SL₀= 0), data within the register

is shifted 1-bit right.

Shift Register using JK Flip-flops

• In section 2.6.5 we have seen that how to construct D flip-flop using JK flip-flop. By applying complement inputs to J and K we can construct serial-in serial-out shift right register using JK flip-flops as shown in the Fig. 4.3.10.

Review Questions

1. Draw a 4-bit serial-in-serial-out shift register and draw its waveforms.  AU May-06, Dec.-06, Marks 8

2. Draw a 4-bit parallel-in-serial-out shift register and briefly explain.  AU May-06, Marks 8

3. Draw the 8-bit serial-in-parallel-out shift register and explain its operation.  AU: Dec.-06, Marks 8

4. Draw and explain the operation of parallel-in-parallel-out shift register.

5. Explain the operation of 4-bit bidirectional shift register with the help of neat diagram.  AU: May-19, Marks 8

6. What are registers ? Construct a 4-bit register using D-flip-flop and explain the operations on the register.  AU Dec.-19, Marks 7